BH-75 - 7,500 lb. Advanced Flat-Plate Boat Hoist

0 Reviews
Composite Price

BH-75 – 7,500 lb. Advanced Flat-Plate Boat Hoist

The BH-75 – 7,500 lb. Advanced Flat-Plate Boat Hoist combines an Elite 1 1/2 HP Painted Wired Boat Lift Motor and an 7,500 lb. Advanced Gear Plate Assembly to create a boat hoist.

The 7,500 lb Advanced Gear Plate Assembly is a gear plate that has a lifting capacity of 7,500 lbs. Assemblies include the 10-inch aluminum die-cast hoist pulley, 96-tooth bronze worm gear assembly, extended block bronze steel assembly, and 34-inch drive belt.

There are no steel-on-steel moving parts. It has been assembled and tested by the manufacturer. Lifetime warranty included. You can choose between galvanized steel or powder-coated steel for the backplate. This item ships in a single box.

Elite 1 1/2 HP Painted Wired Boat Lift Motor are single-phase motors with start capacitors. Standard duty motors. Factory-wired for 220 volts. An electrician can rewire it to 110 volts. Fits all BH-USA flat-plate hoists and gear plates. Fits other brands using the standard 4 ft x 2 ft flat-plate mounting holes.

NEMA 56 frame motor. UL/CSA listed and approved. TENV (totally enclosed, non-ventilating) housing. TENV housing prevents dirt, insects, and water from entering the motor.

Maximum runtime: 15 minutes. Finished in black. Includes colored T-wires. Includes easy-to-follow instructions. Equipment guide and wiring instructions included.

A motor wire harness is installed directly on the electrical motor. Depending on your preference, you can select a maintained (lock-on) or momentary (spring-loaded) drum switch type. The in-line GFCI has a built-in test and reset button.

The extended block worm assembly has a 2-inch bearing block, a worm on a driveshaft, and an aluminum housing with 1/4 inch grease fittings. Attaches directly to the gear plate. The assembly has standard flat-plate mounting holes.

The 96 tooth worm gear assembly comes assembled with the gear, sleeve, backplate bearing, axle sleeve bolt, and snap rings. 1/4 inch easy-reach grease fittings are included. The gear fits standard gear plates used in flat-plate hoists.

The 10 in. Aluminum Die-Cast Hoist Pulley is made from an aluminum die-casting process. Over 15 years of use on BH-USA Flat Plate hoists. They are much stronger in marine environments. They will not swell or bend. The belt-gripping technology on the inside of the pulley prevents belt slippage. Compatible with any known flat-plate hoist. Resistant to warping. Designed to fit drive belts better. The bore is 3/4 inches. Accepts belts up to 1/2 inch.

The AX-34 is a 34-inch drive belt that is compatible with all flat-plate boat hoists from BH-USA. This belt is the perfect length to fit around a 10-inch hoist pulley and to be able to attach it to a 2-inch motor pulley. As the motor’s driveshaft turns, the pulleys turn the belt in order to complete the movement of the hoist.

Gear plates from the Advanced Series feature bronze 96 tooth worm gear assemblies and extended block steel worm assemblies. They are designed to be used with boat lift motors of up to 1 1/2 HP. The only difference between the 7,500 lb and 8,500 lb gear plates is their pulleys. A single belt pulley is used on the 7,500 lb and a dual belt pulley is used on the 8,500 lb.

Safety Caution
It is BH-USA’s recommendation to hire a licensed electrician for wiring or rewiring electrical components

8,500 lb. Advanced Gear Plate AssemblyNever use the same material for both worm gears. The use of steel-on-steel or bronze-on-bronze is not recommended for flat-plate hoists.

Standard Series
Name: BH-30 BH-40
GPA: 4,000 lbs 4,000 lbs
HP: 3/4 1
Duty: Standard Standard
Worm: Bronze Bronze
96 Tooth: Cast Iron Cast Iron
Block: Short Short
Pulley: Single Single
Deluxe Series
Name: BH-35 BH-45 BH-65
GPA: 6,500 lbs 6,500 lbs 6,500 lbs
HP: 3/4 1 1
Duty: Standard Standard HD
Worm: Bronze Bronze Bronze
96 Tooth: Cast Iron Cast Iron Cast Iron
Block: Extended Extended Extended
Pulley: Single Single Single
Advanced Series
Name: BH-75 BH-85
GPA: 7,500 lbs 8,500 lbs
HP: 1 1/2 1 1/2
Duty: Standard Standard
Worm: Steel Steel
96 Tooth: Bronze Bronze
Block: Extended Extended
Pulley: Single Dual
All Flat-Plate Hoists use Elite Motors painted wired boat lift motors.

Rated Capacity: 7500 lbs
Test: Straight-line
Dimensions: 12 in. L x 24 in. H
Plate Thickness: 1/4 in.
Bull Gear Ratio: 96:1
GPA Warranty: Lifetime
Extended Block Worm Assembly
Worm Material: Hardened steel
Thread: Single
Thread Direction: Right hand
Worm Diameter: 1 3/4 in.
 Worm Length: 2 in.
Worm Bore: .754 in.
Grease Fittings: 3
Fitting Size: 1/4 in.
Dimensions: 1 1/4 in. x 1/2 in.
Collars Included: 2
Collar Set Screw: 5/16 in.
96 Tooth Worm Gear Assembly
Material: 932 Bronze
Gear Bore: 2.875 in.
Diameter: 12 3/4 in.
Hub Depth: 2 in.
10 in. Pulley & AX-34 Belt
Material: Aluminum
Type: Die-cast
Holds: 2 belts
Size: 10 in.
Bore: 3/4 in.
Belt Size: 34 in.
Type: Cogged
Hoist Pulley Fits 10 in.
Motor Pulley Fits: 2 in.
Horsepower: 1 1/2 (1.5)
Type: Standard
Finish: Painted
Motor Dimensions:  13″ x 6.5″ x 9.5″
Weight:  35 lbs.
Voltage:  115v / 230v
Amps:  20.0 (115v) / 10.0 (230v)
RPM: 1725 
Hz: 60
Frame: 56
SF:  1.0
Type:  C
AMB:   40ºC
Max. Runtime: 15 min.
Housing: TENV
Code:  L
Thermally Protected: None
Driveshaft Diameter: 2″ x 4″ x 5/16″
Keystock: Included
Keystock Size: 1″ L x 0.75″ W x 0.75″ H
Replacement Start Capacitors: 650 uF
Start Capacitor SKU #: BH02249
OEM Model #:  93043
BH-USA SKU #: 93077
Country of Origin: China
Electric Motor Wire Harness
110v Plug: 3-US 110v Standard
220v Plug: US 240v NEMA 6-15
Switch Size: 3.5″ x 4.5″ x 4.5″
Max. Amps: 20
Max. HP: 1 1/2
Compliance: UL, NEMA, CE, SA
VAC: 120-240
Box Color: Gray
Material: Plastic
Handle: Red
Type: Maintained / Momentary
Cable: 14/5 SJTW
GFCI-to-Plug: 4 1/2 in.
Box-to-GFCI: 60 in.
Class: A-Rainproof
Amp: 15
Hz: 60
Voltage: 125v / 240v
Reset: Automatic
Cord Dia.: .28 – .65
Motor Pulley
Size: 2 in. x 2 in. x 2 in.
Material: Aluminum
Bore Size: 5/8 in. (.630 in.)
Type: Center bore
Set Screw: 3/8 in.
Thread: 16 (coarse)
Build: Machined
Fits: Single / Dual
 Mount: 56-Frame

Product Overview

  • 7,500 lb. Lift Rating
  • Advance series includes a 7,500 lb. gear plate and 1 1/2 hp motor
  • Factory assembled and tested under load
  • No steel-on-steel moving hoist parts
  • Meets UL and NEMA requirements
  • 2 in. motor pulley and 10 in. hoist pulley included
  • Ships in (2) boxes