Elite 1 1/2 HP Stainless C-Face Electric Motor
$ 581.30
UPC: 816146020457
SKU: 93100
In stock
BH-USA Return Policy
Elite 1 1/2 HP Stainless C-Face Electric Motor
The Elite Stainless C-Face Electric Motor are single phase, dual-voltage motors. The stainless steel motors are not wired at all, they have what is called T-Wires and they are loose so at the point of purchase they can be wired either 100v or 220v. Made from stainlesss steel. The NEMA 56 shaft is 0.625 inch thick and 1.88 inch extruding from the motor housing. UL Recognized (C-UL-US). It uses a capacitor to start.
TENV (totally enclosed, non-ventilated) housing. TENV housing prevents dirt, insects, and water from entering the motor. 15 minutes maximum runtime. Includes 1 inch long x 1/4 inch wide keystock, colored T-wires, easy-to-follow wiring instructions, BH-USA equipment guide, and wiring instructions.
|
The C-face input electric motor is used in enclosed boat hoists that do not have belt drives, enclosed gear reduction gearboxes, or worm gear reduction gearboxes. C-face electric motors fit BH-USA A-Drive, BH-USA Enclosed Drive, AMS E-Drive, AMS Series, and Golden C-Drive. Electric motors are compatible with enclosed boat hoists that have a standard C56 flange. |
When wiring or rewiring electrical components, BH-USA recommends hiring a licensed electrician.
Specifications
General Specifications |
|||
|---|---|---|---|
| Weight: | 37.35 lbs. | Individual Box Size: | 15 in. x 10 in. x 10 in. |
| Product Length: | 11.75 in. | Product Width: | 6.50 in. |
| Product Height: | 8.75 in. | Shaft Width: | 0.625 in. |
| Shaft Length: | 2 in. | Country of Origin: | China |
| Model #: | 93049 | Retail SKU: | 93100 |
Nameplate Specifications |
|||
| HP: | 1 | Voltage: | Dual (115v / 230v) |
| Phase: | 1 | Amps: | 15.4 (115v) / 7.7 (230v) |
| RPM: | 1725 | Hz: | 60 |
| Frame: | 56c | Service Factor: | 1.15 |
| SFA: | 17.6 (115v) / 8.8 (230v) | Type: | C |
| AMB: | 40°c | Time: | 15 MIN |
| HSG: | TENV | Code: | E |
| Insulation: | F | Thermally Protected: | None |
| UL: | Recognized | UL Stamp: | C-UL-US |
Technical Specifications |
|||
| Electrical Type: | Capcitor Start | Rotation: | Selective |
| Shaft Type: | NEMA 56 | Shaft Extension: | 1.88 in. |
| Frame Length: | 10.0 in. | Mounting: | Round |
| Drive End Bearing: | Ball | Opp Drive End Bearing: | Ball |
| Frame Material: | Stainless Steel | Replacement Capacitor: | 800 uF |
| Capacitor SKU #: | BH02246 | Keystock: | Included |
| Keystock Length: | 1 in. | Keystock Width: | 0.25 in. |
Product Overview
- C-Face mounting design
- TENV enclosure prevents dirt and elements from entering the motor
- Durable painted frame, capacitor case, and conduit box cover
- Double-shielded bearings extend the service life of the motor
- Time rated 15-minute duty cycle
- UL Recognized & CSA Approved
- Suitable for outdoor environments and weather resistant
These are Marks consumers rarely see because they are specifically used on component parts that are part of a larger product or system. These components may have restrictions on their performance or may be incomplete in construction. The component recognition marking is found on a wide range of products, including some switches, power supplies, printed wiring boards, some kinds of industrial control equipment and thousands of other products.
Just as with the UL Listing and Classified Marks, there are three variations of UL’s Recognized Component Mark: one for the United States only, one for Canada only and one for both the United States and Canada. The C-UR Mark is applied to components only used in the Canadian market. Components with this type of Mark have been evaluated to Canadian standards. The optional C-UL-US Component Recognition Mark indicates compliance with both Canadian and U.S. requirements. UL encourages manufacturers distributing UL Recognized Components evaluated for both countries to use this combined Mark, but they may continue using separate UL Recognized Component Marks for the United States and Canada.
Components covered by UL’s Recognized Component program are intended to be installed in another device, system or end product. They are to be installed at the factory, not in the field and they may have restricted performance capabilities that limit their use. When a complete product or system containing UL Recognized Components is evaluated, the end-product evaluation process can be streamlined.
The UL component evaluation process may include a construction examination and testing. Guidelines addressing the suitability of a component when used in an end product are noted in UL’s test report as conditions of acceptability. This information can also be found in Product iQTM.
All components carrying the UL Recognized Component Mark are covered by UL’s Follow-Up Services program to determine continued compliance with UL’s requirements.
Reviews
Related Products
You may also like...
-
A-Drive 40:90 Drive Shaft Kit
$74.99 – $99.99 Select options -
A-Drive 40:75 Drive Shaft Kit
$86.75 – $99.99 Select options
