8,000 lb. Galvanized Four Post Pile Mount Boat Lift

0 Reviews
$6,731.07
SKU: 50036
UPC: 091037072627

AVAILABLE

Qty.



8,000 lb. Galvanized Four Post Pile Mount Boat Lift

The 8,000 lb. Galvanized Four Post Pile Mount Boat Lift is designed to mount on the tops of four dock pilings. The lift uses a 15 ft. single cable straight-line configuration. This results in an 8,000 lb. lift capacity rating. Features all-welded design. Hot-dipped galvanized finish.

There are no piling mount bolts included.

No cradle bunks included

Includes

(2) Elite Motors 1 HP motors w/ maintained drum switches, GFCIs, and 16 & 45-foot control cable
(2) 12K 13 ft. galvanized top beams with dead man brackets
(1) 16 in. chock angle kit
(4) Guidepost stanchions, PVC pipe, and black 48 in. split bumpers
(2) 4,000 lb. standard powder-coated gear plate assemblies w/ hoist covers
(1) 6K fastener kit
(4) 15 ft. x 5/16 in. 7 x 19 aircraft cable

CRADLE WIDTH MEASUREMENT

6,000-lb galvanized boat lift is equipped with standard 12 ft 6 in cradle beams. If your pilings are already installed, it is essential to obtain a precise center-to-center measurement between the pilings. Your cradle length will be determined by this measurement. When the center-to-center measurement is 12 ft 6 in, then you will need a cradle length of 12 ft 6 in If the correct length of boat cradles is not installed, issues can arise with how the boat lift operates.

PILING DEPTH

To support the weight of the boat, the 8-inch pilings must be installed with enough seabed penetration. Each piling must be square and level with the others. Drive-end pilings (where the boat hoists are installed) should be 6 inches shorter than the other two pilings. After installation, movement of the pilings will affect boat lift operation and safety.

A. HOIST SECUREMENT

BH-USA flat-plate boat hoists are attached to the top beam with 1/2 in x 1 1/2 in bolts (included). Initially, mount the back of the flat-plate cover between the gear plate and the top beam. Align the hole in the drive pipe with the hole in the large gear sleeve. Set the gear sleeve bolt in place and snap the front cover into the back cover.

B. BOAT HOIST CONTROL CABLE

One of the flat-plate boat hoists is wired with an extra cable (45 ft) so that both drum switches can be mounted side-by-side. It is not recommended to wire both flat-plate hoists to one drum switch. For double motorboat lifts, we recommend using the GEM Remotes GR2 double motor boat lift remote. One to two boat lift motors can be operated simultaneously. It was designed to operate this type of lift.

C. TOP BEAM SECUREMENT

Utilize lag or through bolts to secure the top beams to the pilings. Piling attachment bolts are not included.

D. CABLE INSTALLATION

The 10,000 lb & 12,000 lb galvanized boat lifts will come with 123 ft of boat lift cable. Unlike the 6,000 lb and 8,000 lb beams, the 10,000 lb & 12,000 lb beams have deadman brackets welded to each beam to attach your boat lift cable. Compounding blocks are included with boat cradles.

Installation is required. This unit should be assembled by experienced contractors or professionals familiar with boat hoist assembly and installation. Improper installation and maintenance may void the manufacturer’s warranty. The assembly/use instructions should be read and examined before operation.

6,000 lbs. 8,000 lbs. 10,000 lbs. 12,000 lbs.
Pilings 4 4 4 4
GPA Size: 4,000 lbs. 4,000 lbs. 4,000 lbs. 4,000 lbs.
GPA Finish: Powdercoat Powdercoat Powdercoat Powdercoat
Motor Size: 3/4 HP 1 HP 3/4 HP 1 HP
Cable Con. Straight Straight Compound Compound
Thickness: 5/16 in. 5/16 in. 5/16 in. 5/16 in.
Length: 15 ft. 15 ft. 31 ft. 31 ft.
Specifications

Boat Lift Capacity: 8,000 lbs.
Total Weight: 875 lbs.
Shipping Method: Freight
Drive Shaft Size: 2 3/8 in. OD (2 in. ID)
Cable Configuration: Straight-Line
Cable Diameter: 5/16 in.
Cable Material: Galvanized
Cable Length 15 ft.
Cable Amount: 4
Top Beam Structure: Steel WF Beam
Motor Type: Electric
Motor Style: 56 Frame (Clawfoot)
Motor HP: 1 HP
Motor Voltage: 120 Volts
Motor Cable Length: (1) 16 ft. / (1) 45 ft.
Minimum Piling Size: 8 in. Diameter
Cable Winders Included: No
Pipe Bearings 4 / Beam (Welded Sleeves)
Bearing Maintenance: Grease Fittings
Grease Fitting Size: 1/4 in.
Fasteners Galvanized (Included)
Electrical UL, NEMMA, GFCI Protected
UL File E464499
Packaging: Wood Crate (15 ft. x 3 ft. x 2 ft).
Capacity / Per Beam: 6,000 lbs.
Top Beam Dimensions: 13 ft. x 6 in. Web x 4 in. Flange
Top Beam Material: Steel WF Beam
Drive Pipe Support: Dual
Drive Pipe Type: Sch. 40
Drive Pipe Finish: Hot-dipped Galvanized
Drive Pipe OD: 2 3/8 in.
Drive Pipe ID: 2 in.
Pipe Bearings: Galvanized Support
Bearing Maintenance: Greaseable
Grease Fitting Size: 1/4 in.
Grease Fitting Style: Press-In
Dead Man Brackets: Pre-Installed
Compounding Tabs: Welded
Cable Winders: Not Included
Rated Capacity: 4,000 lbs.
Tested Capacity: Straight line
Gear Plate Dimensions: 2 ft. x 1 ft.
Bull Gear Ratio: 96:1
Back Plate Bearing: Bronze Composite
96 Tooth Gear Material: Cast Iron
Worm Material: Hardened Bronze
Hoist Pulley Size: 10 in.
Hoist Pulley Material: Zinc die-cast
Drive Belt Size: 34 in.
Drive Belt Type: AX-34 cogged belt
Weight: 34-47 lbs.
Warranty: Lifetime
Manufacturer: BH-USA
Model #: 60421
Max Run Time: 15 Minutes
Dimensions: 9 in. x 11 in. x 6 in.
Weight: 27 lbs.
Catalog #: N/A
SKU: N/A
Horsepower: 1
Mounting Type: 56 Frame
RPM: 1725
Service Factor: 1.0
Voltage: 115 / 230
Phase: 1
Amps: 7.8
SFtartA: 6.2
Herz: 60
AMB: 40c
Frame: 56
HSG: TENV
Code: L
Insulation: A
Shaft Diameter 5/8 in.
Beam Dimensions: 10 ft. L x 4 in. H x 3 in. flange
Endplate Dimensions: 10 in. L x 3 1/4 in. W
Endplate Thickness: 5/16 in.
Endplates Attachment: Welded before galvanized
Cradle Beam Material: Steel
Cradle Beam Finish: Hot-dipped galvanized
Mounting Holes: 2 (center of endplates)
Mounting Hole Size: 5/8 in.
Cradle Beam Weight: 10 lbs. per ft.
Cable Attachment: Endplates
Weight Rating: 4,000 lbs (distributed load)
Shipment Type: Freight
Shipment Style: Loose Beams
Dimensions: 3 1/2 in. x 4 1/2 in. x 4 1/2 in.
Max Amps: 20
Max HP: 1 1/2 HP
Compliance: UL, NEMA, CE, SA
VAC: 120-240
Weight: 1.2 lbs.
Box Color: Gray
Handle Color: Red
Switch Type: Maintained (Lock-On)
Housing Material: Plastic
Plug Type 3-US 110 V Standard
Plug Cord Length 6 in.
GFCI to Switch Cord Length 6 ft.
GFCI 7 in. x 2 1/2 in. x 1 in.
Color Black
Class A-Rainproof
Catalog Number 303385214
AMP 15
Hz 60
Watt 1875
Volt 125
Reset Type Automatic
Cord Diameter Range .28 – .65

All BH-USA boat lifts are shipped via motor freight and are individually crated. For items delivered freight, it is the responsibility of the purchaser to set up a delivery address that is easily accessible to the freight company and have a forklift at their disposal for unloading the freight. If the customer does not have a fork truck at his or her disposal, the crate must be unloaded by hand. In order to facilitate delivery, BH-USA will request a call from the freight company to the customer. In the event of missed deliveries, the purchaser will be liable for additional freight charges. The purchaser must be present at the time of delivery. See our shipping terms and conditions for more information.

Product Overview

  • 8,000 lb. straight-line cable lifting capacity
  • Mounts to 4 pilings
  • Hot-dipped galvanized top beams
  • Includes (2) 1 HP 110v electric motors for each top beam
  • Includes (2) 4,000 lb. gear plate assemblies
  • Features (2) maintained drum switches
  • In-line GFCI control cable
  • Complete lift ships freight in a crate

Reviews