Short Block Worm Assembly

$ 128.73
SKU: 75614
UPC: 091037756145

Only 5 left in stock


Free Shipping

Free Shipping

BH-USA offers free shipping for retail customers on select items. Products eligible for free shipping will be shipped via UPS Ground. We offer expedited services for those individuals that require a more time-sensitive delivery time. If you add any items that are not free shipping, the cart will calculate and display a shipping price based on ONLY the items that are not free shipping. Whenever free shipping is available, it will appear above the "Add to Cart" button on the product page.



BH-USA has partnered with UPS to offer Ground, Next Day Air, 2nd Day Air, and 3 Day Select services to our customers. In order to ship with these methods, the order must meet UPS's requirements.


Your order will be shipped via the most cost-effective method possible. All shipping and handling charges are the responsibility of the customer. Additionally, they are responsible for any delivery issues that may hinder delivery. In such cases, extra fees can apply, such as residential delivery fees.

Click the button below to learn more about our ordering and shipping policies.

Our Shipping Partners shipping modal logos


Short Block Worm Assembly

The Short Block Worm Assembly has a 2-inch bearing block, a worm on a driveshaft, and an aluminum housing with 1/4 inch grease fittings. Attaches directly to the gear plate. The assembly has standard flat-plate mounting holes.

The assembly is fitted with standard flat-plate mounting holes Factory assembled. Blocks are fitted with flange bushings. They have 1/4-inch grease fittings, which can be accessed easily.

The bronze worm is featured on the Standard series flat-plate boat hoists. On the gear plate, the bronze worm turns the 96-tooth cast iron worm gear. When the flat-plate hoist is assembled, the cast iron worm gear turns the drive pipe.

Worm gears are mounted on the gear plate at the top mounting holes. An assembly block is installed around the middle of the gear plate to match up the gear. When the assembly block’s drive shaft rotates, the worm gear inside the assembly block turns the 96-tooth gear. There is a pulley mounted on the drive shaft of the assembly block, and there is a smaller pulley mounted on the drive shaft of the motor, which is mounted at the bottom of the gear plate. On both pulleys, a belt is installed. The motor rotates its drive shaft in response to the motion of the pulleys on the motor and assembly block, which then turn the worm gear inside the assembly block, which turns the 96 tooth gear. A drive pipe installed through the 96 tooth gear’s bore causes the drive pipe to rotate. If the motor is turning in one direction, or the other, the drive pipe will either raise or lower whatever is attached to it.

There are no mounting fasteners, key stock for the pulley, or pulley included.

Short Block Worm AssemblyNever use the same material for both worm gears. The use of steel-on-steel or bronze-on-bronze is not recommended for flat-plate hoists. Return policy.

Standard Series
Name: BH-30 BH-40
GPA: 4,000 lbs 4,000 lbs
HP: 3/4 1
Duty: Standard Standard
Worm: Bronze Bronze
96 Tooth: Cast Iron Cast Iron
Block: Short Short
Pulley: Single Single
Deluxe Series
Name: BH-35 BH-45 BH-65
GPA: 6,500 lbs 6,500 lbs 6,500 lbs
HP: 3/4 1 1
Duty: Standard Standard HD
Worm: Bronze Bronze Bronze
96 Tooth: Cast Iron Cast Iron Cast Iron
Block: Extended Extended Extended
Pulley: Single Single Single
Advanced Series
Name: BH-75 BH-85
GPA: 7,500 lbs 8,500 lbs
HP: 1 1/2 1 1/2
Duty: Standard Standard
Worm: Steel Steel
96 Tooth: Bronze Bronze
Block: Extended Extended
Pulley: Single Dual
All Flat-Plate Hoists use Elite Motors painted wired boat lift motors.

Worm Type: Bronze
Worm Material: Hardened bronze (660 or 932)
Thread: Single
Thread Direction: Right hand
Worm Diameter: 1 3/4 in.
Worm Length: 2 in.
Worm Bore: .754 in.
Driveshaft Material: Stress proof steel
Driveshaft Length: 11 3/4 in.
Driveshaft Diameter: 746 in.
Grease Fittings: 1
Grease Fitting Size: 1/4 in.
Collar Size: 1 1/4 in. x 1 1/4 in. x 1/2 in.
Collar Amount: 2
Collar Set Screw Size: 5/16 in.

The Boat Hoist USA brand offers machine parts used exclusively in the Boat Hoist USA brand flat-plate hoist. BH-USA brand machined parts should NEVER be used with any other brand flat-plate hoist or machined parts. Any individual machine part or re-built/repaired flat-plate hoist is not warranted by BH-USA. Lift-Tex Inc. assumes no liability for damage to person or property caused by the re-building of a flat plate hoist, regardless of its brand. BH-USA sells non-returnable, non-warrantable machine parts. The user is solely responsible for any machine part purchased and used by them. BH-USA does not guarantee that any individual machined part will solve an existing problem or function as designed. BH-USA recommends that you purchase a new flat-plate hoist that has been built and tested on site at BH-USA rather than trying to repair an existing hoist.

Product Overview

  • Factory assembled
  • Replacement on BH-30 & BH-40 boat hoists (standard series)
  • It fits industry standard for mounting and replacing
  • Made from 6061-T6 US aluminum
  • Features a bronze worm mounted on a hardened steel driveshaft