Galvanized Dual Pipe Support
$139.29 - $207.10
Special Order Item
BH-USA Return Policy
BH-USA Stock Policy
Galvanized Dual Pipe Support for Wood Beams
The Galvanized Dual Pipe Support for Wood Beams mounts directly to overhead wood beams or joists. The supports are stamped and laser cut. Features an 18 in. distance from sleeve to sleeve. 2 in. cable winders will fit between the sleeves. The sleeves have (1) 1/4 in. press-in grease fitting offset from each sleeve. Allows the drive pipe to be greased without uninstalling the drive pipe. The sleeves will accept a 2 3/8 in. OD (2 in. ID) drive pipe. The pipe support sleeves are measured out to line up with the boat hoist with minor adjustments.
The oversized sleeve reduces friction and ensures better load distribution. The sleeve keeps the drive pipe from walking up the side of the sleeve. Made from hot-dipped galvanized steel. The L-Brackets have (3) 3/4 in. round wood beam mounting holes and (1) 2 in. pipe support mounting slot. The entire kit weighs 17.15 pounds. The dual-pipe support measures 25 in. ( L) x 3 1/2 in. (W) x 6 in. (H). The L-Bracket measures 3 3/4 in. (L) x 2 1/2 in. (W) x 9 1/2 in. (H). The sleeves measure 3 1/2 in. (L) x 2 13/16 in. (W) x 2 13/16 (H) Recommended for virtually any type of overhead boat lift.
Pipe support mounting fasteners included.
Wood Beam / Joists mounting fasteners not included.
Dual pipe supports, with or without hoist hanger, is best used in a center mount configuration. A 4,000 lb. maximum rating per hoist hanger when used correctly in center mounting. Side mounting greatly reducts the dual pipe support and hoist hanger capacity. A 1,000 lb. maximum rating when used correctly inside mounting. See the attached guide for more information and limitations.
Specifications
| Pipe Support (w/o L-Brackets) Dimensions: | 25 in. (L) x 3 1/4 in. (W) x 6 in. (H) |
| Pipe Support Type: | Dual |
| Pipe Support Material: | Steel |
| Pipe Support Finish: | Hot-Dipped Galvanized |
| Pipe Support Sleeve Diameter: | 2 7/8 in. (OD) / 2 3/8 in. (ID) |
| Sleeve Fits Drive Pipes: | 2 3/8 in. (OD) / 2 in. (ID) |
| Sleeve Dimensions: | 3 in. (L) x 2 13/16 in. (W) x 2 13/16 in. (H) |
| Between Sleeves: | 18 in. |
| Outside Sleeve to Sleeve: | 25 in. |
| Grease Fitting Size: | 1/4 in. |
| Grease Fitting Amount: | 2 |
| Grease Fitting Placement: | Offset |
| Grease Fitting Type: | Press-In |
| Pipe Support Sleeve Thickness: | 1/4 in. |
| Pipe Support L-Bracket Mounting Slots: | 4 |
| Pipe Support L-Bracket Mounting Slot Size: | 2 in. |
| L-Bracket Dimensions: | 3 3/4 in. (L) x 2 1/2 in. (W) x 9 1/2 in. (H) |
| L-Bracket Adjusts to: | 2 in. – 16 in. |
| Cable Winder Type:: | Varies |
| Cable Winder Fits: | 2 in. |
| L-Bracket Amount: | 2 |
| Wood Beam Mounting Holes (Per L-Bracket): | 3 |
| Wood Beam Mounting Hole Size (Per L-Bracket): | 3/4 in. |
| Drive Pipe Mounting Holes (Per L-Bracket): | 1 |
| Mounting Fasteners: | Included (L-Brackets to Pipe Support Only) |
| Hex Head Bolt Amount: | 2 |
| Hex Head Bolt Size: | 9/16 in. x 1 3/4 in. |
| Hex Head Bolt Finish: | Zinc-plated Galvanized |
| Flat Washer Amount: | 4 |
| Flat Washer Size: | 9/16 in. |
| Flat Washer Finish: | Zinc-plated Galvanized |
| Lock Washer Amount: | 2 |
| Lock Washer Size: | 9/16 in. |
| Lock Washer Finish: | Zinc-plated Galvanized |
| Nut Amount: | 2 |
| Nut Thread: | 12 |
| Nut Size: | 9/16 in. |
| Nut Finish: | Zinc-plated Galvanized |
| Side Mount Rating: | 1,000 lbs. |
| Side Mount Configuration: | Straight-line |
| Twin Mount Rating: | 1,500 lbs. |
| Side Mount Configuration: | Straight-line |
| Center Mount Rating: | 4,000 lbs. |
| Weight | 17.15 lbs. |
| Center Mout Maximum Rating: | 4,000 lbs. |
| Side Mount Maximum Rating: | 1,000 lbs. |
Center-mount pipe supports are only recommended for center mount or twin mount installations. It is not recommended to use pipe support on a side mount installation. Never attempt to straight-line lift any more than 4000 lbs on a side mount overhead lift or straight line more than 6000 lbs on center or twin mount lifts. Only use the full length of the pipe to connect both pipe supports.
Do not attempt to use two short pieces of the drive pipe. If designing or engineering your overhead lift, you must download and read the BH-USA overhead boat lift guide that can be found on this page. Also available in the tech guide section. BH-USA makes available complete engineered and rated lifts and highly encourages choosing this option over designing and engineering a boat lift on your own.
The above ratings of the dual pipe supports are only valid if installing or using the pipe supports with the BH-USA overhead boat lift guide. The Side Mount and Twin Mount ratings are based on straight line pull. Rating is based on per pipe support and not per boat lift. When considering the weight of your boat, you must use full wet weight plus the weight of the boat cradle. (wet weight + boat cradle weight = total lifting weight) BH-USA engineers and manufactures factory-rated complete boat lifts. We highly recommend purchasing one of these boat lifts instead of building your own. If you, or your installer, buys parts and pieces to engineer your custom boat lift, it will no longer be considered a Boat Hoist USA engineered boat lift.
Product Overview
- Fits 2 3/8 in. OD (2 in. ID) drive pipes
- Fits 2 in. cable winders
- Made of hot-dipped galvanized steel
- Mounting brackets adjust up to 16 in. to fit most overhead wood beams
- Features two sleeves with 1/4 in. grease fittings
- Includes L-Bracket mounting fasteners
- Does not include wood beam/joist mounting fasteners
Related Products
You may also like...
-
Galvanized Flat Washers
$0.27 – $0.47 Select options -
Galvanized Nuts
$0.10 – $0.53 Select options -
Galvanized Split Lock Washers
$0.10 – $0.45 Select options -
Stainless Steel Split Lock Washers
$0.09 – $1.08 Select options
